pop logo

How to Build a 3-Tiered Water Storage Rack


MATERIAL COST: < $400 | COMPLEXITY: Simple to Moderate | DURATION: 3-5 Hours

According to the "Prepper Rule of 3" we can only survive 3 days without water. Having clean, potable water is key to any prepper's survial plan - or at least a way to filter water than isn't at a bare minimum.

The fact of the matter is, you need to have in place a lot of redundancies in place when it comes to water preps. Read this blog post to learn more.

One of those redundancies is to have bulk water storage that can be easily accessed in times of emergency. This project helps accomplish this where you can create a storage rack to house three 55 gallon water barrels to use for potable water or a rain catchment system.

The picture to the right is the actual 3-tiered water storage rack that I constructed and put in my garage for clean, potable water. I put water preserver in each of the barrels and only need to change it out every five years.

Follow the instructions below to begin building your own!

Tools & Materials

Tools & Hardware: (Approx $60-$100)

  • Drill, drill bits and drivers
  • Level
  • Square
  • Chalk Line / Pencil
  • Miter & Skill Saw
  • #8x 1½" Wood Screws (Source)
  • #10x 2 ½" Wood Screws (Source)
  • 3/8-16 x 3-1/2" Hex Cap Screws w/Nuts (Source 1) (Source 2)

  • 3 (Qty) 55 Gallon Water Barrels (Source) (Cheap on Facebook Marketplace)

Wood & Cut List: (Approx $120)

  • 16 (Qty) 2" x 4" x 8' (Source)
    - 4 pieces @ 8'
    - 16 pieces @ 32"
    - 6 pieces @ 29"
    - 24 pieces @ 10" (45° angle on one end)

  • 3 (Qty) 1" x 4" x 8' (Source)
    - 6 pieces @ 35"

  • 1 (Qty) 1/2" x 4' x 4' Plywood (Source)
    - 1 piece @ 32" x 32"

Plumbing: (Approx $88)

  • 2 (Qty) 24" Braided Flexible Stainless Steel Water Heater Connector Hose 3/4" (Source)

  • 4 (Qty) Beduan Stainless Steel Pipe Fitting, Male 3/4" Thread, 4" Length (Source)

  • 1 (Qty) 3/4" Spigot (Source)

  • 2 (Qty) Plumber Tape (Source)

Building Instructions

  1. Take inventory and make sure you have all the wood necessary for the project.

  2. Cut all wood material as per the above cut list. If you need to modify the design to fit your space, sketch it out before cutting to determine your true dimensions. (Legs not pictured 4 (Qty) 2" x 4" x 8' Studs)

  3. Layout and screw together the frame for the shelf on which the barrels with rest and for the top storage shelf. (4 pieces @ 32") See Step 4 for a quick sidebar. Front/Back = 32" Sides = 35"

  4. Attach two inside braces about 13" in from the outside edges. This step can be done concurrently with step 2 if desired. (8 pieces @ 29")

  5. Repeat steps 3 and 4 for the three other frames/shelves.

  6. Using a 3/8 drill bit, drill two holes in top of each of the 24 pieces @ 10" with a 45° angle on one end. The holes should be 2.5" from the straight edge and 1" in from the angled edge. These will serve as part of the cradle for the water barrels.

  7. Using 4-6" length screw drill bit, use the 2 1/2" screws and secure these 24 pieces using the drill holes created in step 6 as indicated in the picture to each of the frames. 8 pieces per frame. You'll be using 3 frames/shelves. The fourth is for the top shelf. (Tip: With masking tape, mark 2" on the 4-6" scree drill bit to know how much to screw in the screw.)

  8. Secure the 1" x 4" 35" pieces with 1 1/2" screws. Drill pilot hoes to avoid splitting the wood. Align the 1x4s as shown in the picutre to each angled 2x4.

  9. Confirm that the barrel sit comfortably and appropriately in the crade.

  10. Repeat steps 7 and 8 for the other two frames/shelves.

  11. Stand each frame/shelf up and position them approximately two feet apart. Position so the cradle so it's pointing towards the ceiling and the side you have designated as "front."

  12. Make sure that each of the 4 pieces of the 2" x 4" x 8' studs are exactly 8 feet in length. Adjust to 8 feet if necessary. These will be the legs of the storage rack.

    As you complete steps 14-17 make sure you use the level to ensure proper positioning.

  13. Slide in and position 2 pieces of the 2" x 4" x 8' studs in the corners on the bottom portion of the frame that is laying on the cement. The 2" side of the stud should be facing the ceiling. These will be two of the four legs that will hold the frames in place.

  14. Make sure the top of the studs are flush with the top of the frame and secure in place with four (4) 2 1/2 screws in a 2x2 pattern. 8 screws will be needed for this step - 4 for each stud. You'll need to drill some pilot holes to prevent splitting the wood.

  15. From the bottom of the top frame, measure exactly 24" down and mark it with a pencil on both of the legs (2" x 4" x 8' studs). This is where the top of the next frame/shelf will be positioned.

  16. Instead of using a tape measure for step 15, from the scraps of the 1" x 4" x 8' board, cut to measure 24" and use as a spacer between the shelves.

  17. Position the next frame so the top of the frame (not the 10" piece with a 45° angle on one end) lines up with the marked line from step 15 and secure to the legs as instructed in step 14. However, you don't need to drill pilot holes on this step. Use the 24" spacer wood to easily position the next frame.

  18. Once the frame is in position, clamp it down on both sides to hold in place while you screw the legs into the frame as instructed in step 14.

  19. Repeat steps 15-18 for the next two frames. The two legs should now be secured to each of the four frames that's currently positioned on the bottom.

  20. Carefully flip the entire storage rack over so the top is now on the bottom.

  21. Repeat this process (steps 13-19) for the other two legs, which will be directly opposite of the other two legs. When done, the top two legs should now be secured to each of the four top part of the frames. The bottom frame should be about 12" to the bottom of the legs.

  22. Position and secure the 32" x 35" piece of plywood with the 1 1/2" screws to the very top of the frame before standing it up. This is the top shelf and you'll be able to store supplies on the top.

  23. Stand up the storage rack and take a long good look and the what you've built!

  24. Using the 3/8 drill bit, drill pilot holes in the middle of each of the three frames that will hold the water barrels that are connected to each of the legs for the 3 1/2" bolt, nut, and washer for added strength. (Each barrell full of water weighs about 460 lbs.)

  25. Hammer in the 3 1/2" bolt with washers on each end, then secure each one with the bolt using a socket and cresent wrench.

  26. Position the storage rack to it's new home and insert each of the three water barrels in it's place. Now it's time for the plumbing & filling with water!

This site is not part of the Facebook website or Facebook Inc.

Additionally, this is it NOT endorsed by Facebook in any way.

FACEBOOK is a trademark of FACEBOOK, Inc.

Copyright © 2024 - All Rights Reserved